Popular Flyingbear-Ghost 5 3D Printer Full Metal Frame Diy Kit With Color Gift Tf Shipping From Russia

Ordered 20.09.21 received 16.11.21. Delivery meestexpress, but at the point of issue could not deliver, had to go to the central office in the city. Came with removable drivers. Collected slowly, lubricating all the bearings. One problem is blowing, I print to the fan of the nozzle, but for a long time it is not enough. The printer is very davolen. About the adhesive I recommend glue pencil PvP. I print ABS +: Table 95 ° C, extruder 240 ° C. Also, please pay attention to the protection in case of a breakage of the thermo-sensor on the hotende, the heater continues to warm, the fan on the radiator with the thermal stops This, of course, if the heating of hotend and the firmware Version 8.5.6 is included. With ultrabaza there was a problem, but with the seller, like, solved this question. I'll unsubscribe on the results of this problem. Foamed polyethylene went to the thermobox.

So my old dream came true, I got a 3D printer. Collected slowly, checking and rechecking everything. And he earned! It's really weird. The X axis end worked, but did not let go. Because of this, the team home did not work normally, but I still printed the bolt with the nut. Then there was a long correspondence with support, which then stopped answering. Yes, and I realized that by correspondence this problem is not solved, and bought a new board of the head. It didn't help. I was almost desperate, but I decided to check the fees in the basement. On the switch board, one contact of the connector going to the head was bent. Without removing the fee, I just did not see it, the head does not fit into the printer. This is victory! I should have checked early. Now I'm totally happy. By the way, the drivers are soldered. This is bad. But they are all quiet 2225 and that's good.

Delivery to Ulyanovsk 10 days. He drove without damage. Completeness is OK, gift too. Flyingbear reborn x2.0 card with the ability to replace drivers. Prints out of the box well, immediately tried abs. Then I changed it to myself. Installed direct, backlight in the case, carried the suspension of the filament to the side panel. There was one glitch when printing on WiFi, when the printing from the chicken was canceled, all 3 axles hung. Helped to fill the firmware. In general, while satisfied. In the future, I plan to increase the lining of the case and the front panel with the door, then I will think about buying 2208 and 2209. The printer can be safely recommended and the seller too.

Delivery to Mo is exactly three days from the moment of payment. This is my first 3D printer. Assembly on video instructions 4 hours. But before that, I revised a lot of yutuba on this model and the experience of working as a designer for more than 30 years. I could have collected it without instructions. The quality of the test printing "out of the box" is quite acceptable. From receipt of the printer to receipt of finished parts exactly 6 hours. Which drivers on the board did not understand, but it looks like all the same and quiet. Noisy fans. In the bedroom, perhaps, it is uncomfortable to print, but I have a printer in a topper in a private house. Printer and seller recommend.

At 9 am I received, at 16 already works on the order. Now I have them 2 first year second just started work. Board with non-variable drivers minus. There were difficulties in assembling with the first such was not, namely, with mounting the table, the shafts are fixed slightly closer to each other than necessary, cleaning the table at the bottom point. Another minus delivered to the point of issue and not home is not critical but unpleasant because without the car now and the box is heavy.

I ordered the second one. The printer is good for the first, but given that there is already a tender 3 on the Clipper, I want more. In general, with the task for which I bought (printing a heap of the same parts, several at a time)-cope. Already going raspberry under the Clipper, made direct. The seller answers for a long time, but when he found that the second printer panel is scratched-made a discount. Everything else is sufficient to work quality.

I collected, everything is fine, that's only on the motor on the y axis, I would of course put bolts on more, especially remain in stock, and I watched the video of as as and I have for some reason a smaller one, but come on, in general, the printer is very cool, I advise! And I also put delivery from China to Volgograd came in a week, I so understood the seller shitryl and sent from Russia, but it's even better, I did not have not have

Ordered from Moscow 23 received 28 in Lipetsk near the house in postyatya Pyaterochka. At a discount from Ali and keshbek litisshopa came out 18 rubles. I collected under the evening of the nepeh according to the instructions from amperka. The test hat from the flash drive began to print, interrupted so that I do not waste the filament on the varnish, I will order more drivers 2209 and an easy motor for the director

Fast delivery and chic service! The printer works perfectly. The only negative is the ultrabase to which the plastic does not stick well! I'm going to change it to ordinary glass. The extruder and Z axis drivers are terrible! Change immediately! Ordered, waiting! It's disgusting! Immediately put them and the price is higher! In general, the previous printer was a encoder 3! And this one is more interesting!

Came quickly, in a week and a half. I collected an hour for four (I'm so special and 3D printer at me first). Which is amazing, there were no special difficulties, on the amperka really good instruction turn-based for those who suddenly. In general, we will test further, but so far everything pleases. Thanks :) Of the tiny minuses: one key for screws M6 or something in the kit was not.

In appearance, all the rules. Until I collected and printed. Drivers are removable, mother MKC. The seller asked a question about the motherboard, answered the standard-due to the lack of components .. And so on Anything can come. Came all quickly on December 10 ordered, 16 was on the hands (courier in hand). Delivery was in Penza

Delivery fast in 5 days from the moment of order to the Rt. collected literally in 1,5 hours. Prints on 5 +. The acquisition is happy as Luck) any jambs did not notice packed perfectly. Only I can not find the Wi-Fi, but the printer is not here. I want to protest with TPU plastic, let's see what this bear is capable of)

Torque, lucky with the board. Collected in 1,5 hours thanks to the roller on yutuba from the Russian-speaking dude, quickly and easily. Calibrated and immediately the first SEAL went well. For full happiness, you only need to drive the Z axis to change and the printer in general will become silent. Recommend bear

Before that, I used other printers, collected and tested, changed .. This printer takes its quality in every detail! It feels like engineers made a printer with respect to customers! Excellent packing, going easily. Quality details .. Prints straight from the box on high quality! And 7 days delivery!

For a long time I chose a printer and stopped on it. Brought in a week, delivery in Pyaterochka. The Assembly is not difficult, the Lufts are minimal, everything is laid well in the basement, it pleases. Prints perfectly if you configure the slicer correctly. The seller is great! Good luck to all!

The goods from the warehouse went to St. Petersburg in 4 days. Assembled The printer, adjusted the height of the table, began the trial printing and stopped serving plastic, the spring is deaf stuck. Disassembled the extruder and found a chip between the radiator and fitting of the tube!!!

Great Machine! Delivered by courier DPD in hands. Neat packaging, everything was completely safe. I collected it easily according to the instructions. thanks and prosperity to the seller and people who produce this miracle!!! I recommend to buy!

Faced with the fact that not all the hexagon were in the set =/delivery fast. The box is whole without damage. It's all right. Ties of course in the butt. It's easy, okay. After assembly, immediately ready to print. The price also pleased.

Everything is chic, collected according to the instructions from the amperk site, very detailed instructions. I have already printed 3 coils of PLA and PETG, I got the motherboard Robin Nano in 1,2 with replaceable drivers.

Good Printer, long wanted. I fucked him for an hour. Most of all fucked with the extruder, not so easy to refuel. Well, in general, this is the best printer. I will not upgrade anything yet. Filament ordered waiting.

good choice for 250$. fast shipping from nearby warehouse. I got parcel after week from ordering. you can see printing quality in pictures below (PLA, 60 mm/sec, layer width 0.2 mm)

Everything works fine! Drivers are removable. Prints from the box without additional settings worthy.

The request was processed for a week and a week delivered. Works, the drivers are not unpacked.

I bought the second such printer in this store. Works fine, the drivers are not dirty